GW Instek AFG-3000 Series Arbitrary Waveform Generator

$1,800.00


   
AFG-3081
AFG-3051
Waveforms
Sine, Square, Ramp, Pulse, Noise, DC, Sin(x)/x, Exponential Rise, Exponential Fall, Negative Ramp
Arbitrary Waveforms
ARB Function
Built in
Sample Rate
200 MSa/s
Repetition Rate
100MHz
Waveform Length
1M points
Amplitude Resolution
16 bits
Non-Volatile Memory
Ten 1M waveforms(1)
User define Output Section
Any section from 2 to 1M points
User define Mark Output
Any section from 2 to 1M points
Frequency Characteristics
Range
Sine
80MHz
50MHz
Square
Triangle, Ramp
1MHz
Resolution
1uHz
Accuracy
Stability
±1 ppm 0 to 50℃
±0.3 ppm 18 to 28℃
Aging
±1 ppm, per 1 year
Tolerance
 1 uHz
Output Characteristics(2)
 
 
Amplitude
Range
10 mVpp to 10 Vpp( into 50Ω)
 20 mVpp to 20 Vpp(open-circuit)
Accuracy
± 1% of setting ±1 mVpp
(at 1 kHz,>10 mVpp)
Resolution
0.1 mV or 4 digits
Flatness
± 1% (0.1dB)  <10 MHz   
± 2% (0.2 dB) 10 MHz to 50 MHz 
± 10% (0.9 dB) 50 MHz to 70 MHz
± 20% (1.9 dB)
 70 MHz to 80 MHz 
(sinewave relative to 1 kHz)
Units
Vpp, Vrms, dBm,
Offset
Range
±5 Vpk ac +dc (into 50Ω)
±10Vpk ac +dc (Open circuit)
Accuracy
1% of setting + 2 mV+ 0.5% of amplitude
Waveform Output
Impedance
50Ω typical (fixed)
> 10MΩ (output disabled)
Protection
Short-circuit protected
Overload relay auto-matically disables main output
SYNC Output
Level
TTL-compatible into>1kΩ
Impedance
50Ω nominal
Sinewave Characteristics
Harmonic Distortion(5)
–60 dBc   DC~1 MHz, Ampl<3 Vpp
–55 dBc   DC~1 MHz, Ampl>3 Vpp
–45 dBc   1MHz~5 MHz, Ampl>3 Vpp
–30 dBc   5MHz~80 MHz, Ampl>3 Vpp
Total Harmonic Distortion
< 0.2%+0.1mVrms
DC to 20 kHz
Spurious (non-harmonic)(5)
–60 dBc   DC~1 MHz
–50 dBc   1MHz~20MHz
–50 dBc+ 6 dBc/octave 1MHz~80MHz
Phase Noise
-65dBc typical 10MHz, 30 kHz band
-47dBc typical 80MHz, 30 kHz band
Square wave Characteristics
Rise/Fall Time
<8 nS(3)
Overshoot
< 5%
Asymmetry
1% of period+1 ns
Variable Duty Cycle
20.0% to 80.0% ≦ 25 MHz   
  40.0% to 60.0% 
 25~50MHz  
50.0%(Fixed)   
  50~80MHz   
Jitter
0.01%+525ps  < 2 MHz
0.1%+75ps 
 > 2 MHz  
Ramp Characteristics
Linearity
 0.1% of peak output
Variable Symmetry
0% to 100%
Pulse Characteristics
Period
20ns 2000s
Pulse Width
8ns 1999.9s
Minimum Pulse Width:
     8nS when FREQ≦50MHz 
     5% of setting period when FREQ≦6.5MHz 
Resolution:
     1nS when FREQ≦50MHz 
     1% of setting period when FREQ≦6.5MHz
Overshoot
<5%
Jitter
100 ppm +50 ps
AM Modulation
Carrier Waveforms
Sine, Square, Triangle, Ramp, Pulse, Arb
Modulating Waveforms
Sine, Square, Triangle, Up/Dn Ramp
Modulating Frequency
2 mHz to 20 kHz
Depth
0% to 120.0%
Source
Internal / External
FM Modulation
Carrier Waveforms
Sine, Square, Triangle, Ramp
Modulating Waveforms
Sine, Square, Triangle, Up/Dn Ramp
Modulating Frequency
2 mHz to 20 kHz
Peak Deviation
DC to 80 MHz
DC to 50 MHz
Source
Internal / External
PWM
Carrier Waveforms
Square
Modulating Waveforms
Sine, Square, Triangle, Up/Dn Ramp
Modulating Frequency
2 mHz to 20 kHz
Deviation
0%  100.0% of pulse width
Source
Internal / External
FSK
Carrier Waveforms
Sine, Square, Triangle, Ramp, Pulse
Modulating Waveforms
50% duty cycle square
Internal Rate
2 mHz to 100 kHz
Frequency Range
DC to 80 MHz
DC to 50 MHz
Source
Internal / External
SWEEP
Waveforms
Sine, Square, Triangle, Arb
Type
Linear or Logarithmic
Direction
Up or Down
Start F / Stop FREQ
100 uHz to 80 MHz
100 uHz to 50 MHz
Sweep Time
1 ms to 500 s
Trigger
Single, External, Internal
Marker
Falling edge of Mark signal 
(Programmable frequency)
Source
Internal / External
BURST
Waveforms
Sine, Square, Triangle, Ramp
Frequency
1 uHz to 80 MHz(4)
1 uHz to 50 MHz(4)
Burst Count
1 to 1000000 cycles or Infinite
Start / Stop Phase
-360.0to +360.0
Internal Period
1 ms to 500 s
Gate Source
External Trigger
Trigger Source
Single, External or Internal Rate
Trigger Delay   
N-Cycle, Infinite: 0s to 85 s
External Modulation Input
Type
for AM, FM, Sweep, PWM
Voltage Range
± 5V full scale
Input Impedance
10kΩ
Frequency
DC to 20 kHz
External Trigger Input
Type
for FSK, Burst, Sweep
Input Level
TTL Compatible
Slope
Rising or falling(selectable)
Pulse Width
> 100 ns
Input Impedance
10kΩ,DC coupled
Latency
Sweep
< 10 us (typical)
Burst
< 100 ns (typical)
Jitter
Sweep
2.5 us
Burst
1 ns; except pulse,300 ps
Modulation Output
Type
for AM, FM, Sweep, PWM
Amplitude
Range
1Vpp
Impedance
> 10kΩ typical (fixed)
Trigger Output
Type
for Burst, Sweep
Level
TTL Compatible into 50Ω
Pulse Width
> 450 ns
Maximum Rate
1 MHz
Fan-out
4 TTL load
Impedance
50Ω typical
Marker Output
Type
for ARB, Sweep
Level
TTL Compatible into 50Ω
Fan-out
4 TTL load
Impedance
50Ω typical
Store/Recall
10 Groups of Setting Memories
Interface
GPIB, RS232, USB
Display
4.3 inch TFT LCD
480 × 3 (RGB) × 272
System Characteristics
Configuration Times 
(typical)
Function Change:
      
Standard---->102ms
      
Pulse-------->660ms
      Built-In Arb- >240ms
Frequency Change:
 24ms
Amplitude Change: 
50ms
Offset Change: 
50ms
Select User Arb: 
< 2s for 1M points
Modulation Change:
 < 200ms
Arb Download Times
(typical)
Binary Code
ASCII Code
GPIB / RS-232 (115 Kbps)
USB(Device)
USB(Host)
1M points
189 Sec
34 Sec
70 Sec
512K points
95 Sec
18Sec
35 Sec
256K points
49 Sec
9 Sec
18 Sec
64K points
16 Sec
3 Sec
6 Sec
16K points
7 Sec
830mS
1340 mS
8K points
6 Sec
490mS
780mS
4K points
6 Sec
365mS
520 mS
2K points
5 Sec
300mS
390 mS
General Specifications
Power Source
 AC100240V , 5060Hz
Power Consumption
65 VA
Operating Environment
Temperature to satisfy the specification :  18 ~ 28C
Operating temperature : 0 ~ 40C
Relative Humidity: 
 80%, 0 ~ 40°C
 70%, 35 ~ 40°C
Installation category: CAT 
Operating Altitude
2000 meters
Pollution Degree
IEC 61010 Degree 2, Indoor Use
Storage Temperature
 -10 ~ 70C, Humidity: 70%
Dimensions (WxHxD)
 Bench Top : 265 (W) x 107 (H) x 374 (D)
Weight
Approx. 4kg
Safety Designed to
EN61010-1
EMC Tested to
EN 55011, IEC-61326-1
Accessories
GTL-110× 1
  Instruction Manual×1
Power cord×1